$ sudo sysctl -a
Sysctl settings are exposed via Kubernetes, allowing users to modify certain kernel parameters at runtime for namespaces within a container. Only sysctls that are namespaced can be set independently on pods. If a sysctl is not namespaced, called node-level, it cannot be set within OKD. Moreover, only those sysctls considered safe are whitelisted by default; you can manually enable other unsafe sysctls on the node to be available to the user.
In Linux, the sysctl interface allows an administrator to modify kernel parameters at runtime. Parameters are available via the /proc/sys/ virtual process file system. The parameters cover various subsystems, such as:
kernel (common prefix: kernel.)
networking (common prefix: net.)
virtual memory (common prefix: vm.)
MDADM (common prefix: dev.)
More subsystems are described in Kernel documentation. To get a list of all parameters, you can run:
$ sudo sysctl -a
A number of sysctls are namespaced in today’s Linux kernels. This means that you can set them independently for each pod on a node. Being namespaced is a requirement for sysctls to be accessible in a pod context within Kubernetes.
The following sysctls are known to be namespaced:
Additionally, most of the sysctls in the net.* group are known to be namespaced. Their namespace adoption differs based on the kernel version and distributor.
To check which net.* sysctls are namespaced on your system, run the following command:
$ podman run --rm -ti docker.io/fedora \ /bin/sh -c "dnf install -y findutils && find /proc/sys/ \ | grep -e /proc/sys/net"
Sysctls that are not namespaced are called node-level and must be set manually by the cluster administrator, either by means of the underlying Linux distribution of the nodes, such as by modifying the /etc/sysctls.conf file, or by using a DaemonSet with privileged containers.
Consider marking nodes with special sysctls as tainted. Only schedule pods onto them that need those sysctl settings. Use the taints and toleration feature to mark the nodes.
Sysctls are grouped into safe and unsafe sysctls. In addition to proper namespacing, a safe sysctl must be properly isolated between pods on the same node. This means that if you set a sysctl as safe for one pod it must not:
Influence any other pod on the node
Harm the node’s health
Gain CPU or memory resources outside of the resource limits of a pod
By far, most of the namespaced sysctls are not necessarily considered safe.
Currently, OKD supports, or whitelists, the following sysctls in the safe set:
This list might be extended in future versions when the kubelet supports better isolation mechanisms.
All safe sysctls are enabled by default. All unsafe sysctls are disabled by default, and the cluster administrator must manually enable them on a per-node basis. Pods with disabled unsafe sysctls will be scheduled but will fail to launch.
The cluster administrator can allow certain unsafe sysctls for very special situations such as high-performance or real-time application tuning.
If you want to use unsafe sysctls, cluster administrators must enable them individually on nodes. They can enable only namespaced sysctls.
Due to their nature of being unsafe, the use of unsafe sysctls is at-your-own-risk and can lead to severe problems like wrong behavior of containers, resource shortage, or complete breakage of a node.
kubeletArguments field in the /etc/origin/node/node-config.yaml
file, as described in
Configuring Node Resources, to set the desired unsafe sysctls:
kubeletArguments: allowed-unsafe-sysctls: - "kernel.msg*,net.ipv4.route.min_pmtu"
Restart the node service to apply the changes:
# systemctl restart origin-node
Sysctls are set on pods using the pod’s
applies to all containers in the same pod.
The following example uses the pod
securityContext to set a safe sysctl
kernel.shm_rmid_forced and two unsafe sysctls,
kernel.msgmax. There is no distinction between safe and unsafe sysctls in
To avoid destabilizing your operating system, modify sysctl parameters only after you understand their effects.
Modify the YAML file that defines the pod and add the
securityContext spec, as
shown in the following example:
apiVersion: v1 kind: Pod metadata: name: sysctl-example spec: securityContext: sysctls: - name: kernel.shm_rmid_forced value: "0" - name: net.ipv4.route.min_pmtu value: "552" - name: kernel.msgmax value: "65536" ...